Board index FlightGear Development Aircraft

IT-AUTOFLIGHT RC3 (Beta Testers Needed!) (Page 6)

Questions and discussion about creating aircraft. Flight dynamics, 3d models, cockpits, systems, animation, textures.

IT-AUTOFLIGHT RC3 (Beta Testers Needed!) (Page 6)

Postby Octal450 » Sat Mar 04, 2017 11:14 pm

Hello FG pilots,
ITAF is approaching the end of development, and I will need people to help me test more complex systems.

VNAV:

One of the last new modes is VNAV. This is a VERY COMPLEX mode which has taken me months to work on.

I am in bad need of beta testers. I am working on a VNAV system with the following features:

Climb following waypoint altitude/altitude select restrictions
Descend to meet waypoints at a specified altitude (in route manager) (Descend via RNAV STARs)
Top of Descent calculation and automatic descent if altitude select is lower

and coming later:
Automatic SPD control

To test, make sure your route manager waypoints have altitude. Example: ROKME@5000 will cause the route manager to add the waypoint ROKME at altitude 5000.

The AP will follow this for climb:
CLIMB in FLCH (LVL CHG, SPD BY PITCH) mode until it reaches either the waypoint altitude, or the altitude in the ITAF ALT SELECT, whichever comes first.Then you can adjust the ALT SELECT at or above the waypoint altitude, and it will climb to the waypoint altitude, then after that waypoint, go up to the next closest altitude, etc...

For descend:
When reaching the calculated top of descent point, ITAF will begin to descend to reach the waypoint at the target altitude, but slightly before. If it cannot descend fast enough, FLCH will engage, and it will go down faster, if it needs drag, the ITAF box will show "ADD DRAG" in the VNAV Command Area. When FMS SPD is done, this will avoid the ADD DRAG message as much as possible by changing airspeed. As with climbing, it will stop at the first altitude constraint it hits, either the ITAF ALT SELECT, or the waypoint altitude.


If you would like to help me beta test this system, (I need beta testing before I can install it), PLEASE leave a comment here on this thread. When the time comes around, I will post instructions on where to download the beta copy of the following aircraft, with the system installed.

MD-88 Rename to MD-88
MD-90 Rename to MD-90
737-800 Rename to 737-800
KC-137R Rename to KC-137R
717 Rename to 717
A320Family Rename to A320Family

Any questions, Please Ask.

Thanks,
Josh

EDIT:
If you see your name here, it means you signed up to test:
Flyngo
Darkriser
GabrielYV
J Maverick 16
KL-666

EDIT 2:
THE IT-AUTOFLIGHT CHANGELOG CAN BE VIEWED HERE!

Thank you!
Last edited by Octal450 on Wed Jul 12, 2017 9:09 pm, edited 11 times in total.
Skillset: JSBsim Flight Dynamics, Systems, Canvas, Autoflight/Control, Instrumentation, Animations
Aircraft: A320-family, MD-11, MD-80, Contribs in a few others

Octal450's GitHub|Launcher Catalog
|Airbus Dev Discord|Octal450 Hangar Dev Discord
User avatar
Octal450
 
Posts: 5583
Joined: Tue Oct 06, 2015 1:51 pm
Location: Huntsville, AL
Callsign: WTF411
Version: next
OS: Windows 11

Re: BETA TESTERS NEEDED -- AUTOFLIGHT

Postby Kristogratia » Sun Mar 05, 2017 4:09 am

Great...
I want to actually. But, I have no time to test it. I have a really really busy schedule on a week :(

Regards,
Christogratia I. Simbolon
User avatar
Kristogratia
 
Posts: 128
Joined: Tue Jul 28, 2015 12:33 pm
OS: Windows 11

Re: BETA TESTERS NEEDED -- AUTOFLIGHT

Postby Octal450 » Sun Mar 05, 2017 6:07 am

If you can do just a normal flight with it, that would be fine. I understand however!

Thanks for your interest,
Josh
Skillset: JSBsim Flight Dynamics, Systems, Canvas, Autoflight/Control, Instrumentation, Animations
Aircraft: A320-family, MD-11, MD-80, Contribs in a few others

Octal450's GitHub|Launcher Catalog
|Airbus Dev Discord|Octal450 Hangar Dev Discord
User avatar
Octal450
 
Posts: 5583
Joined: Tue Oct 06, 2015 1:51 pm
Location: Huntsville, AL
Callsign: WTF411
Version: next
OS: Windows 11

Re: BETA TESTERS NEEDED -- AUTOFLIGHT

Postby Flyngo » Sun Mar 05, 2017 7:21 am

Hello,

can do some test flights in Europe (as soon as I have found out why newest FG shows water on already d/led terrain;-).
Flyngo
 
Posts: 66
Joined: Mon Sep 19, 2016 4:47 pm
Location: EDDS
Callsign: KC-URG
Version: 2017.2.1

Re: BETA TESTERS NEEDED -- AUTOFLIGHT

Postby Darkriser » Sun Mar 05, 2017 8:51 pm

I'm usually able to do a short hop (around an hour) on workdays (if my work assignment allows) and sometimes a short
hop at late nights when children fall asleep.
I'm running a self-compiled 'next' branch of git repository, if that doesn't matter.
And I use mouse only for flying so I really would appreciate a working autopilot :-)
Darkriser
 
Posts: 64
Joined: Wed Dec 28, 2016 1:27 pm
Location: LZIB
Version: next
OS: Arch Linux

Re: BETA TESTERS NEEDED -- AUTOFLIGHT

Postby Octal450 » Sun Mar 05, 2017 9:09 pm

OK great, thanks. I'll keep your names in the list, and advise when it's ready.
Skillset: JSBsim Flight Dynamics, Systems, Canvas, Autoflight/Control, Instrumentation, Animations
Aircraft: A320-family, MD-11, MD-80, Contribs in a few others

Octal450's GitHub|Launcher Catalog
|Airbus Dev Discord|Octal450 Hangar Dev Discord
User avatar
Octal450
 
Posts: 5583
Joined: Tue Oct 06, 2015 1:51 pm
Location: Huntsville, AL
Callsign: WTF411
Version: next
OS: Windows 11

Re: BETA TESTERS NEEDED -- AUTOFLIGHT

Postby GabrielYV » Mon Mar 06, 2017 12:52 am

@it0uchpods I am willing to help amigo :)
New Boeing 737-800YV (Improved version) https://github.com/YV3399/737-800YV

Gabriel Hernandez.
GabrielYV
 
Posts: 215
Joined: Sun Dec 13, 2015 7:06 am
Location: Venezuela/Mexico
Callsign: YV3399/YV123B
Version: 2020.3.13
OS: Mac OS

Re: BETA TESTERS NEEDED -- AUTOFLIGHT

Postby Octal450 » Mon Mar 06, 2017 3:41 am

:)
Skillset: JSBsim Flight Dynamics, Systems, Canvas, Autoflight/Control, Instrumentation, Animations
Aircraft: A320-family, MD-11, MD-80, Contribs in a few others

Octal450's GitHub|Launcher Catalog
|Airbus Dev Discord|Octal450 Hangar Dev Discord
User avatar
Octal450
 
Posts: 5583
Joined: Tue Oct 06, 2015 1:51 pm
Location: Huntsville, AL
Callsign: WTF411
Version: next
OS: Windows 11

Re: BETA TESTERS NEEDED -- AUTOFLIGHT

Postby Octal450 » Sat Mar 11, 2017 9:09 pm

Build 155 is pushed.

VNAV is working for climb, but descent is not working yet, so I disabled VNAV. If you want to test climb:

Put in some waypoints with altitude constrictions:

Open DEBUG-->Internal properties

Set /it-autoflight/settings/vnav-test to 1 (or true)

VNAV buttons should be available in ITAF box now.

DESCENDING DOES NOT WORK PROPERLY! DO NOT ATTEMPT IT UNLESS YOU WANT SILLY THINGS TO HAPPEN!
But climbing should be working.

If you push VNAV onthe ground, VNAV will become active at 1500AGL, instead of FLCH.

Please try to put the ALT SEL below the waypoint alt at some point, to make sure, that it holds at the lowest altitude.

[DOWNLOADS]
SEE FIRST POST

Thanks
Josh
Last edited by Octal450 on Fri Mar 24, 2017 6:44 pm, edited 1 time in total.
Skillset: JSBsim Flight Dynamics, Systems, Canvas, Autoflight/Control, Instrumentation, Animations
Aircraft: A320-family, MD-11, MD-80, Contribs in a few others

Octal450's GitHub|Launcher Catalog
|Airbus Dev Discord|Octal450 Hangar Dev Discord
User avatar
Octal450
 
Posts: 5583
Joined: Tue Oct 06, 2015 1:51 pm
Location: Huntsville, AL
Callsign: WTF411
Version: next
OS: Windows 11

Re: BETA TESTERS NEEDED -- AUTOFLIGHT

Postby Flyngo » Tue Mar 14, 2017 9:00 pm

Tested B 738. VNAV sort of works, catures the WP alts, but in climb speeds up to VNE, in descent it does some nervous triming and speeds up a little, so ITAF on 738 needs a check. Thanks.
Flyngo
 
Posts: 66
Joined: Mon Sep 19, 2016 4:47 pm
Location: EDDS
Callsign: KC-URG
Version: 2017.2.1

Re: BETA TESTERS NEEDED -- AUTOFLIGHT

Postby Octal450 » Tue Mar 14, 2017 9:11 pm

Alright, I'll check it, thanks for the report. For future reference, you can put the details here, instead of in a PM, so if another has the same issue, they can just say so, without me needed to check multiple messages. :)

I found why the climbing behavior is erratic.
The nasal script for VNAV doesn't check whether it should be climbing, holding, or descending, it just commands what it "thinks" is right. (which sometimes goes back and forth between VNAV HLD, and VNAV SPD many times)

I'm resolving this in the next update, which should also have working descent.

It works this way:
If we are flying toward a waypoint with an altitude lower than our altitude, and VNAV is active, then when the ITAF MCP alt is set down to at or below the waypoint alt, it will automatically begin descending at the optimal point (TOP OF DESCENT)
If the MCP alt is higher than the waypoint, but lower than the current alt, the same thing will happen, but the aircraft will level off at the MCP alt first, then when the MCP alt is lowered, continue down.

Profile Des (VNAV PTH) will still not be active yet. Please don't expect it to work. If you are really light, or ignore the "ADD DRAG" message, or dont have the MCP alt lowered at the Top of descent point, it may miss the waypoint.

I hope to have it soon.

EDIT: I have completed the CLB part, completely rewritten, and works much much better! The VNAV is now aware if it is climbing, or descending, or supposed to hold altitude. Last thing to do before I push the next build is Top of descent, and make it so it won't descend, until reaching Top of Descent point.

Josh
Skillset: JSBsim Flight Dynamics, Systems, Canvas, Autoflight/Control, Instrumentation, Animations
Aircraft: A320-family, MD-11, MD-80, Contribs in a few others

Octal450's GitHub|Launcher Catalog
|Airbus Dev Discord|Octal450 Hangar Dev Discord
User avatar
Octal450
 
Posts: 5583
Joined: Tue Oct 06, 2015 1:51 pm
Location: Huntsville, AL
Callsign: WTF411
Version: next
OS: Windows 11

Re: BETA TESTERS NEEDED -- AUTOFLIGHT

Postby Octal450 » Fri Mar 24, 2017 6:44 pm

OK Guys:
I have fixed the bugs, and implemented proper top of descent calculation, and descend by speed by pitch function
The build will be pushed in all the test aircrafts within the next 10mins.

Note that optimum descent rate is not made yet, so if it seems like you won't make it down in time for a constriction, increase your airspeed, and you will descend faster.

Testers:
Feel free to redownload, and test please! Thanks! You can now perform full climbing and descending restrictions, and it is fully working. Remember, it also honors the ITAF ALT sel box, so MAKE SURE the SEL box is above/below the target alt, or the plane won't climb/descend

I'll be adding the KC-137R later today.

[DOWNLOADS]
SEE FIRST POST

J
Skillset: JSBsim Flight Dynamics, Systems, Canvas, Autoflight/Control, Instrumentation, Animations
Aircraft: A320-family, MD-11, MD-80, Contribs in a few others

Octal450's GitHub|Launcher Catalog
|Airbus Dev Discord|Octal450 Hangar Dev Discord
User avatar
Octal450
 
Posts: 5583
Joined: Tue Oct 06, 2015 1:51 pm
Location: Huntsville, AL
Callsign: WTF411
Version: next
OS: Windows 11

Re: BETA TESTERS NEEDED -- AUTOFLIGHT

Postby Octal450 » Fri Mar 24, 2017 7:32 pm

KC-137R now available with Build 165, See first post.
Skillset: JSBsim Flight Dynamics, Systems, Canvas, Autoflight/Control, Instrumentation, Animations
Aircraft: A320-family, MD-11, MD-80, Contribs in a few others

Octal450's GitHub|Launcher Catalog
|Airbus Dev Discord|Octal450 Hangar Dev Discord
User avatar
Octal450
 
Posts: 5583
Joined: Tue Oct 06, 2015 1:51 pm
Location: Huntsville, AL
Callsign: WTF411
Version: next
OS: Windows 11

Re: BETA TESTERS NEEDED -- AUTOFLIGHT

Postby Octal450 » Fri Mar 31, 2017 11:58 pm

No-one?
Skillset: JSBsim Flight Dynamics, Systems, Canvas, Autoflight/Control, Instrumentation, Animations
Aircraft: A320-family, MD-11, MD-80, Contribs in a few others

Octal450's GitHub|Launcher Catalog
|Airbus Dev Discord|Octal450 Hangar Dev Discord
User avatar
Octal450
 
Posts: 5583
Joined: Tue Oct 06, 2015 1:51 pm
Location: Huntsville, AL
Callsign: WTF411
Version: next
OS: Windows 11

Re: BETA TESTERS NEEDED -- AUTOFLIGHT

Postby wlbragg » Sat Apr 01, 2017 5:27 am

Hey Josh, I'd help test it but I don't know anything about the aircraft your installing it into and it would take me more time than I have to get comfortable with the aircraft and the autopilot.

I simply don't want to see you get discouraged so I thought I would at least let you know your work is greatly appreciated, even if not immediately used by myself.
Kansas and Ohio/Midwest scenery development.
KEQA, 3AU, KRCP Airport Layout
Intel i7/GeForce RTX 2070/Max-Q
User avatar
wlbragg
 
Posts: 7586
Joined: Sun Aug 26, 2012 12:31 am
Location: Kansas (Tornado Alley), USA
Callsign: WC2020
Version: next
OS: Win10/Linux/RTX 2070

Next

Return to Aircraft

Who is online

Users browsing this forum: No registered users and 17 guests

cron