Board index FlightGear Development Scenery

Genapts failure on EIDW

Questions and discussion about enhancing and populating the FlightGear world.

Genapts failure on EIDW

Postby legoboyvdlp » Tue Oct 02, 2018 8:41 pm

Hi,
I was running genapts850 on EIDW (apt.dat: https://www.dropbox.com/s/g1c0qufc8mvxmhi/apt.dat?dl=0) using the commands:

genapts850 --input=apt.dat --work=work --airport=EIDW --log-level=info


(I removed the --airport= part when I generated all of Ireland, but I tried to regenerate only EIDW to another directory when I saw that it had failed, when I loaded at EIDW in FlightGear, the airport was completely missing!)

Log output:

Code: Select all
=== genapt850 ===================================================================
setting log level to info
:Genapts850 version 2.1.0 running with 1 threads
:Launch command was genapts850
:Input file = apt.dat
:Work directory = work
:Longitude = -180:180
:Latitude = -90:90
:Terrain sources =
:  work/SRTM2-Africa-3
:  work/SRTM2-Australia-3
:  work/SRTM2-Eurasia-3
:  work/SRTM2-Islands-3
:  work/SRTM2-North_America-3
:  work/SRTM2-South_America-3
:  work/DEM-USGS-3
:  work/SRTM-1
:  work/SRTM-3
:  work/SRTM-30
:Nudge = 10
:Set debug Path .
:Adding airport EIDW to parse list
:Finished Adding airport - now parse
EIDW:Found airport EIDW at 1261974
EIDW:
*******************************************************************
EIDW:Start airport EIDW at 1261974: start time Tue Oct  2 21:35:19 2018



It seems to simply fail silently?

I only get folder AirportArea - which is empty - no AirportObj.


Setting log to bulk results in this:

Code: Select all
=== genapt850 ===================================================================
setting log level to bulk
:Genapts850 version 2.1.0 running with 1 threads
:Launch command was genapts850
:Input file = apt.dat
:Work directory = work
:Longitude = -180:180
:Latitude = -90:90
:Terrain sources =
:  work/SRTM2-Africa-3
:  work/SRTM2-Australia-3
:  work/SRTM2-Eurasia-3
:  work/SRTM2-Islands-3
:  work/SRTM2-North_America-3
:  work/SRTM2-South_America-3
:  work/DEM-USGS-3
:  work/SRTM-1
:  work/SRTM-3
:  work/SRTM-30
:Nudge = 10
:Creating AirportArea directory
:Set debug Path .
:Adding airport EIDW to parse list
:Read airport with icao EGAA, and description Belfast Aldergrove
:Read airport with icao EGAC, and description Belfast City
:Read airport with icao EG05, and description Bellarena
:Read airport with icao XEG8BK, and description Blackhill
:Read airport with icao XEG8CR, and description Castlerock
:Read airport with icao EGAB, and description Enniskillen St Angelo
:Read airport with icao EGAE, and description Londonderry Eglinton
:Read airport with icao EG71, and description Movenis
:Read airport with icao XMUL, and description Mullaghmore
:Read airport with icao EGAD, and description Newtownards
:Read airport with icao XEG8SC, and description Slieve Croob
:Read airport with icao XEG8TG, and description Tandragee
:Read airport with icao EGAL, and description [X] Langford Lodge
:Read airport with icao EIIH, and description [H] Midlands Heliport
:Read airport with icao EIGM, and description [X] Gormanston
:Read airport with icao EIFR, and description [H] Finner Camp
:Read airport with icao EIMH, and description Athboy
:Read airport with icao EIAB, and description Abbeyshrule
:Read airport with icao EIME, and description Baldonnel Casement
:Read airport with icao EIBN, and description Bantry
:Read airport with icao EIBT, and description Belmullet
:Read airport with icao EIBR, and description Birr
:Read airport with icao EICS, and description Castleforbes
:Read airport with icao EICD, and description Clifden
:Read airport with icao EICL, and description Clonbullogue-Edenderry
:Read airport with icao EICA, and description Connemara
:Read airport with icao EICK, and description Cork
:Read airport with icao EIDL, and description Donegal
:Read airport with icao EICM, and description Galway
:Read airport with icao EIGN, and description Gowran Grange
:Read airport with icao EIHN, and description Hacketstown
:Read airport with icao EIIB, and description Inishbofin
:Read airport with icao EIIR, and description Inisheer
:Read airport with icao EIMN, and description Inishmaan
:Read airport with icao EIIM, and description Inishmore
:Read airport with icao EIKY, and description Kerry
:Read airport with icao EIKK, and description Kilkenny
:Read airport with icao EIKH, and description Kilrush
:Read airport with icao EIKN, and description Knock
:Read airport with icao EI01, and description Knocksedan
:Read airport with icao EILT, and description Letterkenny
:Read airport with icao EICN, and description Limerick-Coonagh
:Read airport with icao EIMY, and description Moyne
:Read airport with icao EINC, and description Newcastle
:Read airport with icao EIPT, and description Powescourt
:Read airport with icao EIRT, and description Rathcoole
:Read airport with icao EISP, and description Spanish Point
:Read airport with icao EINN, and description Shannon
:Read airport with icao EISG, and description Sligo
:Read airport with icao EITT, and description Trevet
:Read airport with icao EITM, and description Trim
:Read airport with icao EIWT, and description Weston
:Read airport with icao EIWF, and description Waterford
:Read airport with icao EIDW, and description Dublin
:Found airport EIDW at 1261974
:Finished Adding airport - now parse
EIDW:Read airport with icao EIDW, and description Dublin
EIDW:Found airport EIDW at 1261974
EIDW:
*******************************************************************
EIDW:Start airport EIDW at 1261974: start time Tue Oct  2 21:37:13 2018

EIDW:Parsing land airport:    242 1 0 EIDW Dublin
EIDW:Read airport with icao EIDW, and description Dublin
EIDW:Parsing runway: 45.00 1 1 0.25 1 2 0 10  53.42242908 -006.29006788    0    0 3 2 1 1 28  53.42025908 -006.25057188    0    0 3 2 1 0
EIDW:Read runway: (-6.29007,53.4224) to (-6.25057,53.4203) heading: 95.2392 length: 2636.85 width: 45
EIDW:Parsing runway: 61.00 1 0 0.25 0 2 0 16  53.43698649 -006.26197078    0    0 3 1 0 0 34  53.41990249 -006.24958678    0    0 3 6 0 0
EIDW:Read runway: (-6.26197,53.437) to (-6.24959,53.4199) heading: 156.585 length: 2071.9 width: 61
EIDW:Parsing pavement: 1 0.25 45.5000 X1129 tarmac east
EIDW:Creating Closed Poly with st 1 smoothness 0.25 texture heading 45.5 and description X1129 tarmac east
EIDW:Parsing node:  53.43294517 -006.24645884
EIDW:Parsing node:  53.43344561 -006.24566686
EIDW:CLOSEDPOLY::ADDNODE : lon = -6.24646deg, lat = 53.4329deg, elev = 0m
EIDW:   Adding node lon = -6.24646deg, lat = 53.4329deg, elev = 0m to current linear feature 0000000000000000
EIDW:Parsing node:  53.43350011 -006.24532227
EIDW:CLOSEDPOLY::ADDNODE : lon = -6.24567deg, lat = 53.4334deg, elev = 0m
EIDW:Parsing node:  53.43372201 -006.24666425
EIDW:CLOSEDPOLY::ADDNODE : lon = -6.24532deg, lat = 53.4335deg, elev = 0m
EIDW:Parsing node:  53.43360178 -006.24664559  53.43353734 -006.24671240
EIDW:CLOSEDPOLY::ADDNODE : lon = -6.24666deg, lat = 53.4337deg, elev = 0m
EIDW:Parsing node:  53.43360178 -006.24664559
EIDW:Parsing close loop node:  53.43301446 -006.24765709
EIDW:CLOSEDPOLY::ADDNODE : lon = -6.24665deg, lat = 53.4336deg, elev = 0m
EIDW:CLOSEDPOLY::ADDNODE : lon = -6.24766deg, lat = 53.433deg, elev = 0m
EIDW:Close Contour
EIDW:We still have an active linear feature - add the first node to close it
EIDW: LinearFeature::ConvertContour - Creating a contour with 6 nodes
EIDW:adding Linear Anchor node at lon = -6.24646deg, lat = 53.4329deg, elev = 0m
EIDW:adding Linear Anchor node at lon = -6.24567deg, lat = 53.4334deg, elev = 0m
EIDW:adding Linear Anchor node at lon = -6.24532deg, lat = 53.4335deg, elev = 0m
EIDW:
LinearFeature: Quadtratic curve withOUT cp in line : keep quadtratic: X1129 tarmac east - boundary: theta is 77.0997
EIDW:Segment from lon = -6.24666deg, lat = 53.4337deg, elev = 0m to lon = -6.24665deg, lat = 53.4336deg, elev = 0m
EIDW:        Distance is 16.8507 (OK) so num_segs is 8
EIDW:adding Curve Anchor node (type 2) at lon = -6.24666deg, lat = 53.4337deg, elev = 0m
EIDW:   add bezier node (type  2) at lon = -6.24665deg, lat = 53.4337deg, elev = 0m
EIDW:   add bezier node (type  2) at lon = -6.24663deg, lat = 53.4337deg, elev = 0m
EIDW:   add bezier node (type  2) at lon = -6.24662deg, lat = 53.4337deg, elev = 0m
EIDW:   add bezier node (type  2) at lon = -6.24662deg, lat = 53.4337deg, elev = 0m
EIDW:   add bezier node (type  2) at lon = -6.24662deg, lat = 53.4336deg, elev = 0m
EIDW:   add bezier node (type  2) at lon = -6.24662deg, lat = 53.4336deg, elev = 0m
EIDW:   add bezier node (type  2) at lon = -6.24663deg, lat = 53.4336deg, elev = 0m
EIDW:adding Linear Anchor node at lon = -6.24665deg, lat = 53.4336deg, elev = 0m
EIDW:adding Linear Anchor node at lon = -6.24766deg, lat = 53.433deg, elev = 0m
EIDW:Closed COntour : adding last node at lon = -6.24646deg, lat = 53.4329deg, elev = 0m
EIDW:Closing and Adding pavement
EIDW:Converting a poly with 0 holes
EIDW:Creating a contour with 6 nodes
EIDW:
Handling Node 0


EIDW:adding Linear Anchor node at lon = -6.24646deg, lat = 53.4329deg, elev = 0m
EIDW:
Handling Node 1


EIDW:adding Linear Anchor node at lon = -6.24567deg, lat = 53.4334deg, elev = 0m
EIDW:
Handling Node 2


EIDW:adding Linear Anchor node at lon = -6.24532deg, lat = 53.4335deg, elev = 0m
EIDW:
Handling Node 3


EIDW:Segment from lon = -6.24666deg, lat = 53.4337deg, elev = 0m to lon = -6.24665deg, lat = 53.4336deg, elev = 0m
EIDW:        Distance is 16.8507 (OK) so num_segs is 8
EIDW:adding Curve Anchor node (type 2) at lon = -6.24666deg, lat = 53.4337deg, elev = 0m
EIDW:   add bezier node (type  2) at lon = -6.24665deg, lat = 53.4337deg, elev = 0m
EIDW:   add bezier node (type  2) at lon = -6.24663deg, lat = 53.4337deg, elev = 0m
EIDW:   add bezier node (type  2) at lon = -6.24662deg, lat = 53.4337deg, elev = 0m
EIDW:   add bezier node (type  2) at lon = -6.24662deg, lat = 53.4337deg, elev = 0m
EIDW:   add bezier node (type  2) at lon = -6.24662deg, lat = 53.4336deg, elev = 0m
EIDW:   add bezier node (type  2) at lon = -6.24662deg, lat = 53.4336deg, elev = 0m
EIDW:   add bezier node (type  2) at lon = -6.24663deg, lat = 53.4336deg, elev = 0m
EIDW:
Handling Node 4


EIDW:adding Linear Anchor node at lon = -6.24665deg, lat = 53.4336deg, elev = 0m
EIDW:
Handling Node 5


EIDW:adding Linear Anchor node at lon = -6.24766deg, lat = 53.433deg, elev = 0m
remove contour dups : original contour has 13 points
remove_contour_dups: start new iteration
 cur is: lon = -6.24646deg, lat = 53.4329deg, elev = 0m next is : lon = -6.24567deg, lat = 53.4334deg, elev = 0m
 cur is: lon = -6.24567deg, lat = 53.4334deg, elev = 0m next is : lon = -6.24532deg, lat = 53.4335deg, elev = 0m
 cur is: lon = -6.24532deg, lat = 53.4335deg, elev = 0m next is : lon = -6.24666deg, lat = 53.4337deg, elev = 0m
 cur is: lon = -6.24666deg, lat = 53.4337deg, elev = 0m next is : lon = -6.24665deg, lat = 53.4337deg, elev = 0m
 cur is: lon = -6.24665deg, lat = 53.4337deg, elev = 0m next is : lon = -6.24663deg, lat = 53.4337deg, elev = 0m
 cur is: lon = -6.24663deg, lat = 53.4337deg, elev = 0m next is : lon = -6.24662deg, lat = 53.4337deg, elev = 0m
 cur is: lon = -6.24662deg, lat = 53.4337deg, elev = 0m next is : lon = -6.24662deg, lat = 53.4337deg, elev = 0m
 cur is: lon = -6.24662deg, lat = 53.4337deg, elev = 0m next is : lon = -6.24662deg, lat = 53.4336deg, elev = 0m
 cur is: lon = -6.24662deg, lat = 53.4336deg, elev = 0m next is : lon = -6.24662deg, lat = 53.4336deg, elev = 0m
 cur is: lon = -6.24662deg, lat = 53.4336deg, elev = 0m next is : lon = -6.24663deg, lat = 53.4336deg, elev = 0m
 cur is: lon = -6.24663deg, lat = 53.4336deg, elev = 0m next is : lon = -6.24665deg, lat = 53.4336deg, elev = 0m
 cur is: lon = -6.24665deg, lat = 53.4336deg, elev = 0m next is : lon = -6.24766deg, lat = 53.433deg, elev = 0m
 cur is last point: lon = -6.24766deg, lat = 53.433deg, elev = 0m next is first point: lon = -6.24646deg, lat = 53.4329deg, elev = 0m
remove_contour_dups : after 1 iterations, contour has 13 points
EIDW:Parsing pavement: 1 0.25 105.1500 X1129 tarmac east
EIDW:Creating Closed Poly with st 1 smoothness 0.25 texture heading 105.15 and description X1129 tarmac east
EIDW:Parsing node:  53.43380197 -006.24715610
EIDW:Parsing node:  53.43372201 -006.24666425
EIDW:CLOSEDPOLY::ADDNODE : lon = -6.24716deg, lat = 53.4338deg, elev = 0m
EIDW:   Adding node lon = -6.24716deg, lat = 53.4338deg, elev = 0m to current linear feature 0000000000000000
EIDW:Parsing node:  53.43350011 -006.24532227
EIDW:CLOSEDPOLY::ADDNODE : lon = -6.24666deg, lat = 53.4337deg, elev = 0m
EIDW:Parsing node:  53.43324306 -006.24368786
EIDW:CLOSEDPOLY::ADDNODE : lon = -6.24532deg, lat = 53.4335deg, elev = 0m
EIDW:Parsing node:  53.43311931 -006.24292008
EIDW:CLOSEDPOLY::ADDNODE : lon = -6.24369deg, lat = 53.4332deg, elev = 0m
EIDW:Parsing node:  53.43364765 -006.24270833
EIDW:CLOSEDPOLY::ADDNODE : lon = -6.24292deg, lat = 53.4331deg, elev = 0m
EIDW:Parsing node:  53.43369775 -006.24302642
EIDW:CLOSEDPOLY::ADDNODE : lon = -6.24271deg, lat = 53.4336deg, elev = 0m
EIDW:Parsing node:  53.43393992 -006.24454373
EIDW:CLOSEDPOLY::ADDNODE : lon = -6.24303deg, lat = 53.4337deg, elev = 0m
EIDW:Parsing node:  53.43416341 -006.24592466
EIDW:CLOSEDPOLY::ADDNODE : lon = -6.24454deg, lat = 53.4339deg, elev = 0m
EIDW:Parsing close loop node:  53.43431894 -006.24691237
EIDW:CLOSEDPOLY::ADDNODE : lon = -6.24592deg, lat = 53.4342deg, elev = 0m
EIDW:CLOSEDPOLY::ADDNODE : lon = -6.24691deg, lat = 53.4343deg, elev = 0m
EIDW:Close Contour
EIDW:We still have an active linear feature - add the first node to close it
EIDW: LinearFeature::ConvertContour - Creating a contour with 10 nodes
EIDW:adding Linear Anchor node at lon = -6.24716deg, lat = 53.4338deg, elev = 0m
EIDW:adding Linear Anchor node at lon = -6.24666deg, lat = 53.4337deg, elev = 0m
EIDW:adding Linear Anchor node at lon = -6.24532deg, lat = 53.4335deg, elev = 0m
EIDW:adding Linear Anchor node at lon = -6.24369deg, lat = 53.4332deg, elev = 0m
EIDW:adding Linear Anchor node at lon = -6.24292deg, lat = 53.4331deg, elev = 0m
EIDW:adding Linear Anchor node at lon = -6.24271deg, lat = 53.4336deg, elev = 0m
EIDW:adding Linear Anchor node at lon = -6.24303deg, lat = 53.4337deg, elev = 0m
EIDW:adding Linear Anchor node at lon = -6.24454deg, lat = 53.4339deg, elev = 0m
EIDW:adding Linear Anchor node at lon = -6.24592deg, lat = 53.4342deg, elev = 0m
EIDW:adding Linear Anchor node at lon = -6.24691deg, lat = 53.4343deg, elev = 0m
EIDW:Closed COntour : adding last node at lon = -6.24716deg, lat = 53.4338deg, elev = 0m
EIDW:Closing and Adding pavement
EIDW:Converting a poly with 0 holes
EIDW:Creating a contour with 10 nodes
EIDW:
Handling Node 0


EIDW:adding Linear Anchor node at lon = -6.24716deg, lat = 53.4338deg, elev = 0m
EIDW:
Handling Node 1


EIDW:adding Linear Anchor node at lon = -6.24666deg, lat = 53.4337deg, elev = 0m
EIDW:
Handling Node 2


EIDW:adding Linear anchor node at lon = -6.24532deg, lat = 53.4335deg, elev = 0m
EIDW:   add linear node at lon = -6.24451deg, lat = 53.4334deg, elev = 0m
EIDW:
Handling Node 3


EIDW:adding Linear Anchor node at lon = -6.24369deg, lat = 53.4332deg, elev = 0m
EIDW:
Handling Node 4


EIDW:adding Linear Anchor node at lon = -6.24292deg, lat = 53.4331deg, elev = 0m
EIDW:
Handling Node 5


EIDW:adding Linear Anchor node at lon = -6.24271deg, lat = 53.4336deg, elev = 0m
EIDW:
Handling Node 6


EIDW:adding Linear anchor node at lon = -6.24303deg, lat = 53.4337deg, elev = 0m
EIDW:   add linear node at lon = -6.24379deg, lat = 53.4338deg, elev = 0m
EIDW:
Handling Node 7


EIDW:adding Linear Anchor node at lon = -6.24454deg, lat = 53.4339deg, elev = 0m
EIDW:
Handling Node 8


EIDW:adding Linear Anchor node at lon = -6.24592deg, lat = 53.4342deg, elev = 0m
EIDW:
Handling Node 9


EIDW:adding Linear Anchor node at lon = -6.24691deg, lat = 53.4343deg, elev = 0m
remove contour dups : original contour has 12 points
remove_contour_dups: start new iteration
 cur is: lon = -6.24716deg, lat = 53.4338deg, elev = 0m next is : lon = -6.24666deg, lat = 53.4337deg, elev = 0m
 cur is: lon = -6.24666deg, lat = 53.4337deg, elev = 0m next is : lon = -6.24532deg, lat = 53.4335deg, elev = 0m
 cur is: lon = -6.24532deg, lat = 53.4335deg, elev = 0m next is : lon = -6.24451deg, lat = 53.4334deg, elev = 0m
 cur is: lon = -6.24451deg, lat = 53.4334deg, elev = 0m next is : lon = -6.24369deg, lat = 53.4332deg, elev = 0m
 cur is: lon = -6.24369deg, lat = 53.4332deg, elev = 0m next is : lon = -6.24292deg, lat = 53.4331deg, elev = 0m
 cur is: lon = -6.24292deg, lat = 53.4331deg, elev = 0m next is : lon = -6.24271deg, lat = 53.4336deg, elev = 0m
 cur is: lon = -6.24271deg, lat = 53.4336deg, elev = 0m next is : lon = -6.24303deg, lat = 53.4337deg, elev = 0m
 cur is: lon = -6.24303deg, lat = 53.4337deg, elev = 0m next is : lon = -6.24379deg, lat = 53.4338deg, elev = 0m
 cur is: lon = -6.24379deg, lat = 53.4338deg, elev = 0m next is : lon = -6.24454deg, lat = 53.4339deg, elev = 0m
 cur is: lon = -6.24454deg, lat = 53.4339deg, elev = 0m next is : lon = -6.24592deg, lat = 53.4342deg, elev = 0m
 cur is: lon = -6.24592deg, lat = 53.4342deg, elev = 0m next is : lon = -6.24691deg, lat = 53.4343deg, elev = 0m
 cur is last point: lon = -6.24691deg, lat = 53.4343deg, elev = 0m next is first point: lon = -6.24716deg, lat = 53.4338deg, elev = 0m
remove_contour_dups : after 1 iterations, contour has 12 points
EIDW:Parsing pavement: 2 0.35 105.1100 X1129 conc mid
EIDW:Creating Closed Poly with st 2 smoothness 0.35 texture heading 105.11 and description X1129 conc mid
EIDW:Parsing node:  53.43520555 -006.25586206
EIDW:Parsing node:  53.43380197 -006.24715610
EIDW:CLOSEDPOLY::ADDNODE : lon = -6.25586deg, lat = 53.4352deg, elev = 0m
EIDW:   Adding node lon = -6.25586deg, lat = 53.4352deg, elev = 0m to current linear feature 0000000000000000
EIDW:Parsing node:  53.43431894 -006.24691237
EIDW:CLOSEDPOLY::ADDNODE : lon = -6.24716deg, lat = 53.4338deg, elev = 0m
EIDW:Parsing close loop node:  53.43572421 -006.25563033
EIDW:CLOSEDPOLY::ADDNODE : lon = -6.24691deg, lat = 53.4343deg, elev = 0m
EIDW:CLOSEDPOLY::ADDNODE : lon = -6.25563deg, lat = 53.4357deg, elev = 0m
EIDW:Close Contour
EIDW:We still have an active linear feature - add the first node to close it
EIDW: LinearFeature::ConvertContour - Creating a contour with 4 nodes
EIDW:adding Linear Anchor node at lon = -6.25586deg, lat = 53.4352deg, elev = 0m
EIDW:adding Linear Anchor node at lon = -6.24716deg, lat = 53.4338deg, elev = 0m
EIDW:adding Linear Anchor node at lon = -6.24691deg, lat = 53.4343deg, elev = 0m
EIDW:adding Linear Anchor node at lon = -6.25563deg, lat = 53.4357deg, elev = 0m
EIDW:Closed COntour : adding last node at lon = -6.25586deg, lat = 53.4352deg, elev = 0m
EIDW:Closing and Adding pavement
EIDW:Converting a poly with 0 holes
EIDW:Creating a contour with 4 nodes
EIDW:
Handling Node 0


EIDW:adding Linear anchor node at lon = -6.25586deg, lat = 53.4352deg, elev = 0m
EIDW:   add linear node at lon = -6.25441deg, lat = 53.435deg, elev = 0m
EIDW:   add linear node at lon = -6.25296deg, lat = 53.4347deg, elev = 0m
EIDW:   add linear node at lon = -6.25151deg, lat = 53.4345deg, elev = 0m
EIDW:   add linear node at lon = -6.25006deg, lat = 53.4343deg, elev = 0m
EIDW:   add linear node at lon = -6.24861deg, lat = 53.434deg, elev = 0m
EIDW:
Handling Node 1


EIDW:adding Linear Anchor node at lon = -6.24716deg, lat = 53.4338deg, elev = 0m
EIDW:
Handling Node 2


EIDW:adding Linear anchor node at lon = -6.24691deg, lat = 53.4343deg, elev = 0m
EIDW:   add linear node at lon = -6.24816deg, lat = 53.4345deg, elev = 0m
EIDW:   add linear node at lon = -6.2494deg, lat = 53.4347deg, elev = 0m
EIDW:   add linear node at lon = -6.25065deg, lat = 53.4349deg, elev = 0m
EIDW:   add linear node at lon = -6.25189deg, lat = 53.4351deg, elev = 0m
EIDW:   add linear node at lon = -6.25314deg, lat = 53.4353deg, elev = 0m
EIDW:   add linear node at lon = -6.25438deg, lat = 53.4355deg, elev = 0m
EIDW:
Handling Node 3


EIDW:adding Linear Anchor node at lon = -6.25563deg, lat = 53.4357deg, elev = 0m
remove contour dups : original contour has 15 points
remove_contour_dups: start new iteration
 cur is: lon = -6.25586deg, lat = 53.4352deg, elev = 0m next is : lon = -6.25441deg, lat = 53.435deg, elev = 0m
 cur is: lon = -6.25441deg, lat = 53.435deg, elev = 0m next is : lon = -6.25296deg, lat = 53.4347deg, elev = 0m
 cur is: lon = -6.25296deg, lat = 53.4347deg, elev = 0m next is : lon = -6.25151deg, lat = 53.4345deg, elev = 0m
 cur is: lon = -6.25151deg, lat = 53.4345deg, elev = 0m next is : lon = -6.25006deg, lat = 53.4343deg, elev = 0m
 cur is: lon = -6.25006deg, lat = 53.4343deg, elev = 0m next is : lon = -6.24861deg, lat = 53.434deg, elev = 0m
 cur is: lon = -6.24861deg, lat = 53.434deg, elev = 0m next is : lon = -6.24716deg, lat = 53.4338deg, elev = 0m
 cur is: lon = -6.24716deg, lat = 53.4338deg, elev = 0m next is : lon = -6.24691deg, lat = 53.4343deg, elev = 0m
 cur is: lon = -6.24691deg, lat = 53.4343deg, elev = 0m next is : lon = -6.24816deg, lat = 53.4345deg, elev = 0m
 cur is: lon = -6.24816deg, lat = 53.4345deg, elev = 0m next is : lon = -6.2494deg, lat = 53.4347deg, elev = 0m
 cur is: lon = -6.2494deg, lat = 53.4347deg, elev = 0m next is : lon = -6.25065deg, lat = 53.4349deg, elev = 0m
 cur is: lon = -6.25065deg, lat = 53.4349deg, elev = 0m next is : lon = -6.25189deg, lat = 53.4351deg, elev = 0m
 cur is: lon = -6.25189deg, lat = 53.4351deg, elev = 0m next is : lon = -6.25314deg, lat = 53.4353deg, elev = 0m
 cur is: lon = -6.25314deg, lat = 53.4353deg, elev = 0m next is : lon = -6.25438deg, lat = 53.4355deg, elev = 0m
 cur is: lon = -6.25438deg, lat = 53.4355deg, elev = 0m next is : lon = -6.25563deg, lat = 53.4357deg, elev = 0m
 cur is last point: lon = -6.25563deg, lat = 53.4357deg, elev = 0m next is first point: lon = -6.25586deg, lat = 53.4352deg, elev = 0m
remove_contour_dups : after 1 iterations, contour has 15 points
EIDW:Parsing pavement: 1 0.25 195.8700 X1129 tarmac mid
EIDW:Creating Closed Poly with st 1 smoothness 0.25 texture heading 195.87 and description X1129 tarmac mid
EIDW:Parsing node:  53.43591412 -006.25763823
EIDW:Parsing node:  53.43538906 -006.25701691
EIDW:CLOSEDPOLY::ADDNODE : lon = -6.25764deg, lat = 53.4359deg, elev = 0m
EIDW:   Adding node lon = -6.25764deg, lat = 53.4359deg, elev = 0m to current linear feature 0000000000000000
EIDW:Parsing node:  53.43520555 -006.25586206
EIDW:CLOSEDPOLY::ADDNODE : lon = -6.25702deg, lat = 53.4354deg, elev = 0m
EIDW:Parsing node:  53.43572421 -006.25563033
EIDW:CLOSEDPOLY::ADDNODE : lon = -6.25586deg, lat = 53.4352deg, elev = 0m
EIDW:Parsing close loop node:  53.43611160 -006.25802506
EIDW:CLOSEDPOLY::ADDNODE : lon = -6.25563deg, lat = 53.4357deg, elev = 0m
EIDW:CLOSEDPOLY::ADDNODE : lon = -6.25803deg, lat = 53.4361deg, elev = 0m
EIDW:Close Contour
EIDW:We still have an active linear feature - add the first node to close it
EIDW: LinearFeature::ConvertContour - Creating a contour with 5 nodes
EIDW:adding Linear Anchor node at lon = -6.25764deg, lat = 53.4359deg, elev = 0m
EIDW:adding Linear Anchor node at lon = -6.25702deg, lat = 53.4354deg, elev = 0m
EIDW:adding Linear Anchor node at lon = -6.25586deg, lat = 53.4352deg, elev = 0m
EIDW:adding Linear Anchor node at lon = -6.25563deg, lat = 53.4357deg, elev = 0m
EIDW:adding Linear Anchor node at lon = -6.25803deg, lat = 53.4361deg, elev = 0m
EIDW:Closed COntour : adding last node at lon = -6.25764deg, lat = 53.4359deg, elev = 0m
EIDW:Closing and Adding pavement
EIDW:Converting a poly with 0 holes
EIDW:Creating a contour with 5 nodes
EIDW:
Handling Node 0


EIDW:adding Linear Anchor node at lon = -6.25764deg, lat = 53.4359deg, elev = 0m
EIDW:
Handling Node 1


EIDW:adding Linear Anchor node at lon = -6.25702deg, lat = 53.4354deg, elev = 0m
EIDW:
Handling Node 2


EIDW:adding Linear Anchor node at lon = -6.25586deg, lat = 53.4352deg, elev = 0m
EIDW:
Handling Node 3


EIDW:adding Linear anchor node at lon = -6.25563deg, lat = 53.4357deg, elev = 0m
EIDW:   add linear node at lon = -6.25683deg, lat = 53.4359deg, elev = 0m
EIDW:
Handling Node 4


EIDW:adding Linear Anchor node at lon = -6.25803deg, lat = 53.4361deg, elev = 0m
remove contour dups : original contour has 6 points
remove_contour_dups: start new iteration
 cur is: lon = -6.25764deg, lat = 53.4359deg, elev = 0m next is : lon = -6.25702deg, lat = 53.4354deg, elev = 0m
 cur is: lon = -6.25702deg, lat = 53.4354deg, elev = 0m next is : lon = -6.25586deg, lat = 53.4352deg, elev = 0m
 cur is: lon = -6.25586deg, lat = 53.4352deg, elev = 0m next is : lon = -6.25563deg, lat = 53.4357deg, elev = 0m
 cur is: lon = -6.25563deg, lat = 53.4357deg, elev = 0m next is : lon = -6.25683deg, lat = 53.4359deg, elev = 0m
 cur is: lon = -6.25683deg, lat = 53.4359deg, elev = 0m next is : lon = -6.25803deg, lat = 53.4361deg, elev = 0m
 cur is last point: lon = -6.25803deg, lat = 53.4361deg, elev = 0m next is first point: lon = -6.25764deg, lat = 53.4359deg, elev = 0m
remove_contour_dups : after 1 iterations, contour has 6 points
EIDW:Parsing pavement: 1 0.25 105.5000 X1129-D3
EIDW:Creating Closed Poly with st 1 smoothness 0.25 texture heading 105.5 and description X1129-D3
EIDW:Parsing node:  53.43588004 -006.26067325
EIDW:Parsing node:  53.43588004 -006.26067325  53.43593783 -006.26069486
EIDW:Parsing node:  53.43595520 -006.26054041  53.43594365 -006.26047346
EIDW:CLOSEDPOLY::ADDNODE : lon = -6.26067deg, lat = 53.4359deg, elev = 0m
EIDW:   Adding node lon = -6.26067deg, lat = 53.4359deg, elev = 0m to current linear feature 0000000000000000
EIDW:Parsing node:  53.43595520 -006.26054041
EIDW:Parsing node:  53.43558872 -006.25826744
EIDW:CLOSEDPOLY::ADDNODE : lon = -6.26054deg, lat = 53.436deg, elev = 0m
EIDW:Parsing node:  53.43543915 -006.25732344
EIDW:CLOSEDPOLY::ADDNODE : lon = -6.25827deg, lat = 53.4356deg, elev = 0m
EIDW:Parsing node:  53.43538906 -006.25701691
EIDW:CLOSEDPOLY::ADDNODE : lon = -6.25732deg, lat = 53.4354deg, elev = 0m
EIDW:Parsing node:  53.43591412 -006.25763823
EIDW:CLOSEDPOLY::ADDNODE : lon = -6.25702deg, lat = 53.4354deg, elev = 0m
EIDW:Parsing node:  53.43611160 -006.25802506
EIDW:CLOSEDPOLY::ADDNODE : lon = -6.25764deg, lat = 53.4359deg, elev = 0m
EIDW:Parsing node:  53.43659373 -006.26102763
EIDW:CLOSEDPOLY::ADDNODE : lon = -6.25803deg, lat = 53.4361deg, elev = 0m
EIDW:Parsing node:  53.43659373 -006.26102763  53.43661663 -006.26114973
EIDW:Parsing node:  53.43671812 -006.26127586  53.43675988 -006.26131430
EIDW:CLOSEDPOLY::ADDNODE : lon = -6.26103deg, lat = 53.4366deg, elev = 0m
EIDW:Parsing close loop node:  53.43671812 -006.26127586
EIDW:CLOSEDPOLY::ADDNODE : lon = -6.26128deg, lat = 53.4367deg, elev = 0m
EIDW:Close Contour
EIDW:We still have an active linear feature - add the first node to close it
EIDW: LinearFeature::ConvertContour - Creating a contour with 9 nodes
EIDW:
LinearFeature: Cubic curve withOUT cp1 in line : keep quadtratic: X1129-D3 - boundary: theta is 75.9139
EIDW:
               AND cp2 NOT in line : X1129-D3 - boundary: theta is 117.443
EIDW:Segment from lon = -6.26067deg, lat = 53.4359deg, elev = 0m to lon = -6.26054deg, lat = 53.436deg, elev = 0m
EIDW:        Distance is 17.868 (OK) so num_segs is 8
EIDW:adding Curve Anchor node (type 3) at lon = -6.26067deg, lat = 53.4359deg, elev = 0m
EIDW:   add bezier node (type  3) at lon = -6.26068deg, lat = 53.4359deg, elev = 0m
EIDW:   add bezier node (type  3) at lon = -6.26067deg, lat = 53.4359deg, elev = 0m
EIDW:   add bezier node (type  3) at lon = -6.26066deg, lat = 53.4359deg, elev = 0m
EIDW:   add bezier node (type  3) at lon = -6.26064deg, lat = 53.4359deg, elev = 0m
EIDW:   add bezier node (type  3) at lon = -6.26062deg, lat = 53.436deg, elev = 0m
EIDW:   add bezier node (type  3) at lon = -6.26059deg, lat = 53.436deg, elev = 0m
EIDW:   add bezier node (type  3) at lon = -6.26057deg, lat = 53.436deg, elev = 0m
EIDW:adding Linear Anchor node at lon = -6.26054deg, lat = 53.436deg, elev = 0m
EIDW:adding Linear Anchor node at lon = -6.25827deg, lat = 53.4356deg, elev = 0m
EIDW:adding Linear Anchor node at lon = -6.25732deg, lat = 53.4354deg, elev = 0m
EIDW:adding Linear Anchor node at lon = -6.25702deg, lat = 53.4354deg, elev = 0m
EIDW:adding Linear Anchor node at lon = -6.25764deg, lat = 53.4359deg, elev = 0m
EIDW:adding Linear Anchor node at lon = -6.25803deg, lat = 53.4361deg, elev = 0m
EIDW:
LinearFeature: Cubic curve withOUT cp1 in line : keep quadtratic: X1129-D3 - boundary: theta is 151.801
EIDW:
               AND cp2 NOT in line : X1129-D3 - boundary: theta is 154.127
EIDW:Segment from lon = -6.26103deg, lat = 53.4366deg, elev = 0m to lon = -6.26128deg, lat = 53.4367deg, elev = 0m
EIDW:        Distance is 22.6492 (OK) so num_segs is 8
EIDW:adding Curve Anchor node (type 3) at lon = -6.26103deg, lat = 53.4366deg, elev = 0m
EIDW:   add bezier node (type  3) at lon = -6.26107deg, lat = 53.4366deg, elev = 0m
EIDW:   add bezier node (type  3) at lon = -6.26111deg, lat = 53.4366deg, elev = 0m
EIDW:   add bezier node (type  3) at lon = -6.26115deg, lat = 53.4366deg, elev = 0m
EIDW:   add bezier node (type  3) at lon = -6.26118deg, lat = 53.4366deg, elev = 0m
EIDW:   add bezier node (type  3) at lon = -6.26121deg, lat = 53.4367deg, elev = 0m
EIDW:   add bezier node (type  3) at lon = -6.26124deg, lat = 53.4367deg, elev = 0m
EIDW:   add bezier node (type  3) at lon = -6.26126deg, lat = 53.4367deg, elev = 0m
EIDW:adding Linear Anchor node at lon = -6.26128deg, lat = 53.4367deg, elev = 0m
EIDW:Closed COntour : adding last node at lon = -6.26067deg, lat = 53.4359deg, elev = 0m
EIDW:Closing and Adding pavement
EIDW:Converting a poly with 0 holes
EIDW:Creating a contour with 9 nodes
EIDW:
Handling Node 0


EIDW:Segment from lon = -6.26067deg, lat = 53.4359deg, elev = 0m to lon = -6.26054deg, lat = 53.436deg, elev = 0m
EIDW:        Distance is 17.868 (OK) so num_segs is 8
EIDW:adding Curve Anchor node (type 3) at lon = -6.26067deg, lat = 53.4359deg, elev = 0m
EIDW:   add bezier node (type  3) at lon = -6.26068deg, lat = 53.4359deg, elev = 0m
EIDW:   add bezier node (type  3) at lon = -6.26067deg, lat = 53.4359deg, elev = 0m
EIDW:   add bezier node (type  3) at lon = -6.26066deg, lat = 53.4359deg, elev = 0m
EIDW:   add bezier node (type  3) at lon = -6.26064deg, lat = 53.4359deg, elev = 0m
EIDW:   add bezier node (type  3) at lon = -6.26062deg, lat = 53.436deg, elev = 0m
EIDW:   add bezier node (type  3) at lon = -6.26059deg, lat = 53.436deg, elev = 0m
EIDW:   add bezier node (type  3) at lon = -6.26057deg, lat = 53.436deg, elev = 0m
EIDW:
Handling Node 1


EIDW:adding Linear anchor node at lon = -6.26054deg, lat = 53.436deg, elev = 0m
EIDW:   add linear node at lon = -6.2594deg, lat = 53.4358deg, elev = 0m
EIDW:
Handling Node 2


EIDW:adding Linear Anchor node at lon = -6.25827deg, lat = 53.4356deg, elev = 0m
EIDW:
Handling Node 3


EIDW:adding Linear Anchor node at lon = -6.25732deg, lat = 53.4354deg, elev = 0m
EIDW:
Handling Node 4


EIDW:adding Linear Anchor node at lon = -6.25702deg, lat = 53.4354deg, elev = 0m
EIDW:
Handling Node 5


EIDW:adding Linear Anchor node at lon = -6.25764deg, lat = 53.4359deg, elev = 0m
EIDW:
Handling Node 6


EIDW:adding Linear anchor node at lon = -6.25803deg, lat = 53.4361deg, elev = 0m
EIDW:   add linear node at lon = -6.25903deg, lat = 53.4363deg, elev = 0m
EIDW:   add linear node at lon = -6.26003deg, lat = 53.4364deg, elev = 0m
EIDW:
Handling Node 7


EIDW:Segment from lon = -6.26103deg, lat = 53.4366deg, elev = 0m to lon = -6.26128deg, lat = 53.4367deg, elev = 0m
EIDW:        Distance is 22.6492 (OK) so num_segs is 8
EIDW:adding Curve Anchor node (type 3) at lon = -6.26103deg, lat = 53.4366deg, elev = 0m
EIDW:   add bezier node (type  3) at lon = -6.26107deg, lat = 53.4366deg, elev = 0m
EIDW:   add bezier node (type  3) at lon = -6.26111deg, lat = 53.4366deg, elev = 0m
EIDW:   add bezier node (type  3) at lon = -6.26115deg, lat = 53.4366deg, elev = 0m
EIDW:   add bezier node (type  3) at lon = -6.26118deg, lat = 53.4366deg, elev = 0m
EIDW:   add bezier node (type  3) at lon = -6.26121deg, lat = 53.4367deg, elev = 0m
EIDW:   add bezier node (type  3) at lon = -6.26124deg, lat = 53.4367deg, elev = 0m
EIDW:   add bezier node (type  3) at lon = -6.26126deg, lat = 53.4367deg, elev = 0m
EIDW:
Handling Node 8


EIDW:adding Linear anchor node at lon = -6.26128deg, lat = 53.4367deg, elev = 0m
EIDW:   add linear node at lon = -6.26097deg, lat = 53.4363deg, elev = 0m
remove contour dups : original contour has 27 points
remove_contour_dups: start new iteration
 cur is: lon = -6.26067deg, lat = 53.4359deg, elev = 0m next is : lon = -6.26068deg, lat = 53.4359deg, elev = 0m
 cur is: lon = -6.26068deg, lat = 53.4359deg, elev = 0m next is : lon = -6.26067deg, lat = 53.4359deg, elev = 0m
 cur is: lon = -6.26067deg, lat = 53.4359deg, elev = 0m next is : lon = -6.26066deg, lat = 53.4359deg, elev = 0m
 cur is: lon = -6.26066deg, lat = 53.4359deg, elev = 0m next is : lon = -6.26064deg, lat = 53.4359deg, elev = 0m
 cur is: lon = -6.26064deg, lat = 53.4359deg, elev = 0m next is : lon = -6.26062deg, lat = 53.436deg, elev = 0m
 cur is: lon = -6.26062deg, lat = 53.436deg, elev = 0m next is : lon = -6.26059deg, lat = 53.436deg, elev = 0m
 cur is: lon = -6.26059deg, lat = 53.436deg, elev = 0m next is : lon = -6.26057deg, lat = 53.436deg, elev = 0m
 cur is: lon = -6.26057deg, lat = 53.436deg, elev = 0m next is : lon = -6.26054deg, lat = 53.436deg, elev = 0m
 cur is: lon = -6.26054deg, lat = 53.436deg, elev = 0m next is : lon = -6.2594deg, lat = 53.4358deg, elev = 0m
 cur is: lon = -6.2594deg, lat = 53.4358deg, elev = 0m next is : lon = -6.25827deg, lat = 53.4356deg, elev = 0m
 cur is: lon = -6.25827deg, lat = 53.4356deg, elev = 0m next is : lon = -6.25732deg, lat = 53.4354deg, elev = 0m
 cur is: lon = -6.25732deg, lat = 53.4354deg, elev = 0m next is : lon = -6.25702deg, lat = 53.4354deg, elev = 0m
 cur is: lon = -6.25702deg, lat = 53.4354deg, elev = 0m next is : lon = -6.25764deg, lat = 53.4359deg, elev = 0m
 cur is: lon = -6.25764deg, lat = 53.4359deg, elev = 0m next is : lon = -6.25803deg, lat = 53.4361deg, elev = 0m
 cur is: lon = -6.25803deg, lat = 53.4361deg, elev = 0m next is : lon = -6.25903deg, lat = 53.4363deg, elev = 0m
 cur is: lon = -6.25903deg, lat = 53.4363deg, elev = 0m next is : lon = -6.26003deg, lat = 53.4364deg, elev = 0m
 cur is: lon = -6.26003deg, lat = 53.4364deg, elev = 0m next is : lon = -6.26103deg, lat = 53.4366deg, elev = 0m
 cur is: lon = -6.26103deg, lat = 53.4366deg, elev = 0m next is : lon = -6.26107deg, lat = 53.4366deg, elev = 0m
 cur is: lon = -6.26107deg, lat = 53.4366deg, elev = 0m next is : lon = -6.26111deg, lat = 53.4366deg, elev = 0m
 cur is: lon = -6.26111deg, lat = 53.4366deg, elev = 0m next is : lon = -6.26115deg, lat = 53.4366deg, elev = 0m
 cur is: lon = -6.26115deg, lat = 53.4366deg, elev = 0m next is : lon = -6.26118deg, lat = 53.4366deg, elev = 0m
 cur is: lon = -6.26118deg, lat = 53.4366deg, elev = 0m next is : lon = -6.26121deg, lat = 53.4367deg, elev = 0m
 cur is: lon = -6.26121deg, lat = 53.4367deg, elev = 0m next is : lon = -6.26124deg, lat = 53.4367deg, elev = 0m
 cur is: lon = -6.26124deg, lat = 53.4367deg, elev = 0m next is : lon = -6.26126deg, lat = 53.4367deg, elev = 0m
 cur is: lon = -6.26126deg, lat = 53.4367deg, elev = 0m next is : lon = -6.26128deg, lat = 53.4367deg, elev = 0m
 cur is: lon = -6.26128deg, lat = 53.4367deg, elev = 0m next is : lon = -6.26097deg, lat = 53.4363deg, elev = 0m
 cur is last point: lon = -6.26097deg, lat = 53.4363deg, elev = 0m next is first point: lon = -6.26067deg, lat = 53.4359deg, elev = 0m
remove_contour_dups : after 1 iterations, contour has 27 points
EIDW:Parsing pavement: 1 0.25 105.0000 X1129 tarmac west
EIDW:Creating Closed Poly with st 1 smoothness 0.25 texture heading 105 and description X1129 tarmac west
EIDW:Parsing node:  53.43682162 -006.26234689
EIDW:Parsing node:  53.43629362 -006.26256468
EIDW:CLOSEDPOLY::ADDNODE : lon = -6.26235deg, lat = 53.4368deg, elev = 0m
EIDW:   Adding node lon = -6.26235deg, lat = 53.4368deg, elev = 0m to current linear feature 0000000000000000
EIDW:Parsing node:  53.43625862 -006.26233668
EIDW:CLOSEDPOLY::ADDNODE : lon = -6.26256deg, lat = 53.4363deg, elev = 0m
EIDW:Parsing node:  53.43620662 -006.26200968
EIDW:CLOSEDPOLY::ADDNODE : lon = -6.26234deg, lat = 53.4363deg, elev = 0m
EIDW:Parsing node:  53.43620662 -006.26200968  53.43619362 -006.26192768
EIDW:CLOSEDPOLY::ADDNODE : lon = -6.26201deg, lat = 53.4362deg, elev = 0m
EIDW:Parsing node:  53.43609262 -006.26180868  53.43604762 -006.26177468
EIDW:CLOSEDPOLY::ADDNODE : lon = -6.26201deg, lat = 53.4362deg, elev = 0m
EIDW:Parsing close loop node:  53.43609262 -006.26180868
EIDW:CLOSEDPOLY::ADDNODE : lon = -6.26181deg, lat = 53.4361deg, elev = 0m
EIDW:Close Contour
EIDW:We still have an active linear feature - add the first node to close it
EIDW: LinearFeature::ConvertContour - Creating a contour with 6 nodes
EIDW:adding Linear Anchor node at lon = -6.26235deg, lat = 53.4368deg, elev = 0m
EIDW:adding Linear Anchor node at lon = -6.26256deg, lat = 53.4363deg, elev = 0m
EIDW:adding Linear Anchor node at lon = -6.26234deg, lat = 53.4363deg, elev = 0m
EIDW:
LinearFeature: Quadtratic curve with cp in line : convert to linear: X1129 tarmac west - boundary: theta is 0
EIDW:adding Linear Anchor node at lon = -6.26201deg, lat = 53.4362deg, elev = 0m
EIDW:
LinearFeature: Cubic curve withOUT cp1 in line : keep quadtratic: X1129 tarmac west - boundary: theta is 148.686
EIDW:
               AND cp2 NOT in line : X1129 tarmac west - boundary: theta is 149.522
EIDW:Segment from lon = -6.26201deg, lat = 53.4362deg, elev = 0m to lon = -6.26181deg, lat = 53.4361deg, elev = 0m
EIDW:        Distance is 19.5444 (OK) so num_segs is 8
EIDW:adding Curve Anchor node (type 3) at lon = -6.26201deg, lat = 53.4362deg, elev = 0m
EIDW:   add bezier node (type  3) at lon = -6.26198deg, lat = 53.4362deg, elev = 0m
EIDW:   add bezier node (type  3) at lon = -6.26195deg, lat = 53.4362deg, elev = 0m
EIDW:   add bezier node (type  3) at lon = -6.26192deg, lat = 53.4362deg, elev = 0m
EIDW:   add bezier node (type  3) at lon = -6.26189deg, lat = 53.4362deg, elev = 0m
EIDW:   add bezier node (type  3) at lon = -6.26187deg, lat = 53.4361deg, elev = 0m
EIDW:   add bezier node (type  3) at lon = -6.26184deg, lat = 53.4361deg, elev = 0m
EIDW:   add bezier node (type  3) at lon = -6.26182deg, lat = 53.4361deg, elev = 0m
EIDW:adding Linear Anchor node at lon = -6.26181deg, lat = 53.4361deg, elev = 0m
EIDW:Closed COntour : adding last node at lon = -6.26235deg, lat = 53.4368deg, elev = 0m
EIDW:Closing and Adding pavement
EIDW:Converting a poly with 0 holes
EIDW:Creating a contour with 6 nodes
EIDW:
Handling Node 0


EIDW:adding Linear Anchor node at lon = -6.26235deg, lat = 53.4368deg, elev = 0m
EIDW:
Handling Node 1


EIDW:adding Linear Anchor node at lon = -6.26256deg, lat = 53.4363deg, elev = 0m
EIDW:
Handling Node 2


EIDW:adding Linear Anchor node at lon = -6.26234deg, lat = 53.4363deg, elev = 0m
EIDW:
Handling Node 3


EIDW:Segment from lon = -6.26201deg, lat = 53.4362deg, elev = 0m to lon = -6.26201deg, lat = 53.4362deg, elev = 0m
EIDW:        Distance is 11.2768 (OK) so num_segs is 8
EIDW:adding Curve Anchor node (type 2) at lon = -6.26201deg, lat = 53.4362deg, elev = 0m
EIDW:   add bezier node (type  2) at lon = -6.26203deg, lat = 53.4362deg, elev = 0m
EIDW:   add bezier node (type  2) at lon = -6.26204deg, lat = 53.4362deg, elev = 0m
EIDW:   add bezier node (type  2) at lon = -6.26205deg, lat = 53.4362deg, elev = 0m
EIDW:   add bezier node (type  2) at lon = -6.26205deg, lat = 53.4362deg, elev = 0m
EIDW:   add bezier node (type  2) at lon = -6.26205deg, lat = 53.4362deg, elev = 0m
EIDW:   add bezier node (type  2) at lon = -6.26204deg, lat = 53.4362deg, elev = 0m
EIDW:   add bezier node (type  2) at lon = -6.26203deg, lat = 53.4362deg, elev = 0m
EIDW:
Handling Node 4


EIDW:Segment from lon = -6.26201deg, lat = 53.4362deg, elev = 0m to lon = -6.26181deg, lat = 53.4361deg, elev = 0m
EIDW:        Distance is 19.5444 (OK) so num_segs is 8
EIDW:adding Curve Anchor node (type 3) at lon = -6.26201deg, lat = 53.4362deg, elev = 0m
EIDW:   add bezier node (type  3) at lon = -6.26198deg, lat = 53.4362deg, elev = 0m
EIDW:   add bezier node (type  3) at lon = -6.26195deg, lat = 53.4362deg, elev = 0m
EIDW:   add bezier node (type  3) at lon = -6.26192deg, lat = 53.4362deg, elev = 0m
EIDW:   add bezier node (type  3) at lon = -6.26189deg, lat = 53.4362deg, elev = 0m
EIDW:   add bezier node (type  3) at lon = -6.26187deg, lat = 53.4361deg, elev = 0m
EIDW:   add bezier node (type  3) at lon = -6.26184deg, lat = 53.4361deg, elev = 0m
EIDW:   add bezier node (type  3) at lon = -6.26182deg, lat = 53.4361deg, elev = 0m
EIDW:
Handling Node 5


EIDW:adding Linear Anchor node at lon = -6.26181deg, lat = 53.4361deg, elev = 0m
remove contour dups : original contour has 20 points
remove_contour_dups: start new iteration
 cur is: lon = -6.26235deg, lat = 53.4368deg, elev = 0m next is : lon = -6.26256deg, lat = 53.4363deg, elev = 0m
 cur is: lon = -6.26256deg, lat = 53.4363deg, elev = 0m next is : lon = -6.26234deg, lat = 53.4363deg, elev = 0m
 cur is: lon = -6.26234deg, lat = 53.4363deg, elev = 0m next is : lon = -6.26201deg, lat = 53.4362deg, elev = 0m
 cur is: lon = -6.26201deg, lat = 53.4362deg, elev = 0m next is : lon = -6.26203deg, lat = 53.4362deg, elev = 0m
 cur is: lon = -6.26203deg, lat = 53.4362deg, elev = 0m next is : lon = -6.26204deg, lat = 53.4362deg, elev = 0m
 cur is: lon = -6.26204deg, lat = 53.4362deg, elev = 0m next is : lon = -6.26205deg, lat = 53.4362deg, elev = 0m
 cur is: lon = -6.26205deg, lat = 53.4362deg, elev = 0m next is : lon = -6.26205deg, lat = 53.4362deg, elev = 0m
 cur is: lon = -6.26205deg, lat = 53.4362deg, elev = 0m next is : lon = -6.26205deg, lat = 53.4362deg, elev = 0m
 cur is: lon = -6.26205deg, lat = 53.4362deg, elev = 0m next is : lon = -6.26204deg, lat = 53.4362deg, elev = 0m
 cur is: lon = -6.26204deg, lat = 53.4362deg, elev = 0m next is : lon = -6.26203deg, lat = 53.4362deg, elev = 0m
 cur is: lon = -6.26203deg, lat = 53.4362deg, elev = 0m next is : lon = -6.26201deg, lat = 53.4362deg, elev = 0m
 cur is: lon = -6.26201deg, lat = 53.4362deg, elev = 0m next is : lon = -6.26198deg, lat = 53.4362deg, elev = 0m
 cur is: lon = -6.26198deg, lat = 53.4362deg, elev = 0m next is : lon = -6.26195deg, lat = 53.4362deg, elev = 0m
 cur is: lon = -6.26195deg, lat = 53.4362deg, elev = 0m next is : lon = -6.26192deg, lat = 53.4362deg, elev = 0m
 cur is: lon = -6.26192deg, lat = 53.4362deg, elev = 0m next is : lon = -6.26189deg, lat = 53.4362deg, elev = 0m
 cur is: lon = -6.26189deg, lat = 53.4362deg, elev = 0m next is : lon = -6.26187deg, lat = 53.4361deg, elev = 0m
 cur is: lon = -6.26187deg, lat = 53.4361deg, elev = 0m next is : lon = -6.26184deg, lat = 53.4361deg, elev = 0m
 cur is: lon = -6.26184deg, lat = 53.4361deg, elev = 0m next is : lon = -6.26182deg, lat = 53.4361deg, elev = 0m
 cur is: lon = -6.26182deg, lat = 53.4361deg, elev = 0m next is : lon = -6.26181deg, lat = 53.4361deg, elev = 0m
 cur is last point: lon = -6.26181deg, lat = 53.4361deg, elev = 0m next is first point: lon = -6.26235deg, lat = 53.4368deg, elev = 0m
remove_contour_dups : after 1 iterations, contour has 20 points
EIDW:Parsing pavement: 1 0.25 275.0200 B7RwyThold
EIDW:Creating Closed Poly with st 1 smoothness 0.25 texture heading 275.02 and description B7RwyThold
EIDW:Parsing node:  53.42271110 -006.29084725
EIDW:Parsing node:  53.42221028 -006.29092094
EIDW:CLOSEDPOLY::ADDNODE : lon = -6.29085deg, lat = 53.4227deg, elev = 0m
EIDW:   Adding node lon = -6.29085deg, lat = 53.4227deg, elev = 0m to current linear feature 0000000000000000
EIDW:Parsing node:  53.42216561 -006.29010697
EIDW:CLOSEDPOLY::ADDNODE : lon = -6.29092deg, lat = 53.4222deg, elev = 0m
EIDW:Parsing close loop node:  53.42267123 -006.29002981
EIDW:CLOSEDPOLY::ADDNODE : lon = -6.29011deg, lat = 53.4222deg, elev = 0m
EIDW:CLOSEDPOLY::ADDNODE : lon = -6.29003deg, lat = 53.4227deg, elev = 0m
EIDW:Close Contour
EIDW:We still have an active linear feature - add the first node to close it
EIDW: LinearFeature::ConvertContour - Creating a contour with 4 nodes
EIDW:adding Linear Anchor node at lon = -6.29085deg, lat = 53.4227deg, elev = 0m
EIDW:adding Linear Anchor node at lon = -6.29092deg, lat = 53.4222deg, elev = 0m
EIDW:adding Linear Anchor node at lon = -6.29011deg, lat = 53.4222deg, elev = 0m
EIDW:adding Linear Anchor node at lon = -6.29003deg, lat = 53.4227deg, elev = 0m
EIDW:Closed COntour : adding last node at lon = -6.29085deg, lat = 53.4227deg, elev = 0m
EIDW:Closing and Adding pavement
EIDW:Converting a poly with 0 holes
EIDW:Creating a contour with 4 nodes
EIDW:
Handling Node 0


EIDW:adding Linear Anchor node at lon = -6.29085deg, lat = 53.4227deg, elev = 0m
EIDW:
Handling Node 1


EIDW:adding Linear Anchor node at lon = -6.29092deg, lat = 53.4222deg, elev = 0m
EIDW:
Handling Node 2


EIDW:adding Linear Anchor node at lon = -6.29011deg, lat = 53.4222deg, elev = 0m
EIDW:
Handling Node 3


EIDW:adding Linear Anchor node at lon = -6.29003deg, lat = 53.4227deg, elev = 0m
remove contour dups : original contour has 4 points
remove_contour_dups: start new iteration
 cur is: lon = -6.29085deg, lat = 53.4227deg, elev = 0m next is : lon = -6.29092deg, lat = 53.4222deg, elev = 0m
 cur is: lon = -6.29092deg, lat = 53.4222deg, elev = 0m next is : lon = -6.29011deg, lat = 53.4222deg, elev = 0m
 cur is: lon = -6.29011deg, lat = 53.4222deg, elev = 0m next is : lon = -6.29003deg, lat = 53.4227deg, elev = 0m
 cur is last point: lon = -6.29003deg, lat = 53.4227deg, elev = 0m next is first point: lon = -6.29085deg, lat = 53.4227



any ideas?
User avatar
legoboyvdlp
 
Posts: 5832
Joined: Sat Jul 26, 2014 1:28 am
Callsign: YV-LEGO
Version: 2018.3.1
OS: Windows 10 HP

Re: Genapts failure on EIDW

Postby xDraconian » Wed Oct 03, 2018 12:36 am

Look like it never finished reading the apt.dat file.
Does your apt.dat end with a "99" record?

Find the last thing it was processing before it crashed...
cur is: lon = -6.29085deg, lat = 53.4227deg, elev = 0m next is : lon = -6.29092deg, lat = 53.4222deg, elev = 0m
cur is: lon = -6.29092deg, lat = 53.4222deg, elev = 0m next is : lon = -6.29011deg, lat = 53.4222deg, elev = 0m
cur is: lon = -6.29011deg, lat = 53.4222deg, elev = 0m next is : lon = -6.29003deg, lat = 53.4227deg, elev = 0m
cur is last point: lon = -6.29003deg, lat = 53.4227deg, elev = 0m next is first point: lon = -6.29085deg, lat = 53.4227

Examine what the apt.dat file contains after the above elements.
xDraconian
 
Posts: 86
Joined: Sun Jan 21, 2018 5:53 am
Version: Git
OS: Linux Mint

Re: Genapts failure on EIDW

Postby legoboyvdlp » Wed Oct 03, 2018 12:40 am

I'll take a look now.
User avatar
legoboyvdlp
 
Posts: 5832
Joined: Sat Jul 26, 2014 1:28 am
Callsign: YV-LEGO
Version: 2018.3.1
OS: Windows 10 HP

Re: Genapts failure on EIDW

Postby legoboyvdlp » Wed Oct 03, 2018 12:47 am

Sorry - not possible to look at it on Android. I'll look at it tomorrow.
User avatar
legoboyvdlp
 
Posts: 5832
Joined: Sat Jul 26, 2014 1:28 am
Callsign: YV-LEGO
Version: 2018.3.1
OS: Windows 10 HP

Re: Genapts failure on EIDW

Postby BecOzIcan » Wed Oct 03, 2018 4:39 am

From my own experience the process can be very long AND appears complete where it's not.

For Example, using the GUI, I get the progress bar complete in under 2 minutes but the process still runs in the background (I can see it from my Windows Task Manager showing GENAPTS still running and sucking up 100% or my resources),

Similarly to your experience AirportArea is generated pretty quickly BUT it takes another 2 hours or so for the Airport Object ito actually show up. I notice you can speed things up by using less elements in WED. For example all of my Yellow centre lines are made of only 5 distinct elements (To do that you will eventually have more than one line between two nodes have you 'move back' to trace the next line but this has no impact on the final result AND WED allows you to make some lines transparent.

In two words, be patient. Maybe get GENAPS tio run overnight and see if you collect an airport the next morning.

Cheers
Ian
Current Projects: AI Traffic, Models & Liveries
User avatar
BecOzIcan
 
Posts: 973
Joined: Tue Oct 04, 2011 10:43 pm
Location: Sydney, NSW, Australia
Version: 2.12
OS: Win10

Re: Genapts failure on EIDW

Postby legoboyvdlp » Wed Oct 03, 2018 8:12 am

Genapts simply stops working - it is no longer runnng in the task manager (and with --airport removed, continues on to the next airport). In the cmd window, it is waiting for the next prompt (flashing cursor after >)
User avatar
legoboyvdlp
 
Posts: 5832
Joined: Sat Jul 26, 2014 1:28 am
Callsign: YV-LEGO
Version: 2018.3.1
OS: Windows 10 HP

Re: Genapts failure on EIDW

Postby legoboyvdlp » Wed Oct 03, 2018 12:18 pm

xDraconian wrote in Wed Oct 03, 2018 12:36 am:Look like it never finished reading the apt.dat file.
Does your apt.dat end with a "99" record?

Find the last thing it was processing before it crashed...
cur is: lon = -6.29085deg, lat = 53.4227deg, elev = 0m next is : lon = -6.29092deg, lat = 53.4222deg, elev = 0m
cur is: lon = -6.29092deg, lat = 53.4222deg, elev = 0m next is : lon = -6.29011deg, lat = 53.4222deg, elev = 0m
cur is: lon = -6.29011deg, lat = 53.4222deg, elev = 0m next is : lon = -6.29003deg, lat = 53.4227deg, elev = 0m
cur is last point: lon = -6.29003deg, lat = 53.4227deg, elev = 0m next is first point: lon = -6.29085deg, lat = 53.4227

Examine what the apt.dat file contains after the above elements.



Yes, it does end with 99. I'm checking for the last thing now.


The next element after B7RwyThold is B7RwyEntry:
I copied it exactly as it was in the apt.dat file:
Code: Select all
110 1 0.25 172.9800 B7RwyEntry
111  53.42325928 -006.29093208
111  53.42277343 -006.29084038
111  53.42271110 -006.29084725
111  53.42267123 -006.29002981
111  53.42273194 -006.29002045
112  53.42295912 -006.29032319  53.42316499 -006.29036592
111  53.42295912 -006.29032319
113  53.42330897 -006.29040300
User avatar
legoboyvdlp
 
Posts: 5832
Joined: Sat Jul 26, 2014 1:28 am
Callsign: YV-LEGO
Version: 2018.3.1
OS: Windows 10 HP

Re: Genapts failure on EIDW

Postby legoboyvdlp » Wed Oct 03, 2018 12:36 pm

Trying to run the file on the web generator resulted in

Code: Select all
*** Error in `./genapts850': malloc(): memory corruption: 0x000075d070590390 ***
User avatar
legoboyvdlp
 
Posts: 5832
Joined: Sat Jul 26, 2014 1:28 am
Callsign: YV-LEGO
Version: 2018.3.1
OS: Windows 10 HP

Re: Genapts failure on EIDW

Postby wlbragg » Wed Oct 03, 2018 4:36 pm

@legoboyvdlp have you tried editing the apt.dat file (even line by line) or try another airport and see if it is successful?
What I am getting at is the question, is it just this one airport that is causing a problem? If so, I have had to edit a line or two out of an apt.dat file to get past a portion that the compiler didn't like.
Kansas(2-27-15)/Ohio/Midwest scenery development.
KEQA (2-27-15), 3AU, KRCP Airport Layout
User avatar
wlbragg
 
Posts: 4183
Joined: Sat Aug 25, 2012 11:31 pm
Location: Kansas (Tornado Alley), USA
Callsign: WC2020
Version: next
OS: Win10/Debain/nVGT640

Re: Genapts failure on EIDW

Postby Alant » Wed Oct 03, 2018 6:06 pm

It looks as if this was saved by WED in a format that is too new.
When I open with WED it looks OK, but I can notsave the apt.dat in an old format, getting messages such as:-

Error: ATC Taxi Routes are only supported in X-plane 10 and newer.
Error: Ramp starts with specific traffic and types are only supported in X-plane 10 and newer.

Try removing these and saving the apt.dat as an older version.

Alan
Alant
 
Posts: 750
Joined: Wed Jun 23, 2010 5:58 am
Location: Portugal
Callsign: Tarnish99
Version: from Git
OS: Windows 10

Re: Genapts failure on EIDW

Postby legoboyvdlp » Wed Oct 03, 2018 6:35 pm

I had no trouble with any other airports using the same format.
User avatar
legoboyvdlp
 
Posts: 5832
Joined: Sat Jul 26, 2014 1:28 am
Callsign: YV-LEGO
Version: 2018.3.1
OS: Windows 10 HP

Re: Genapts failure on EIDW

Postby Alant » Wed Oct 03, 2018 7:36 pm

Perhaps the other airports do not have "ATC Taxi Routes" and "Ramp starts with specific traffic and types", and any other unsupported WED 8.50 features. ?
Alant
 
Posts: 750
Joined: Wed Jun 23, 2010 5:58 am
Location: Portugal
Callsign: Tarnish99
Version: from Git
OS: Windows 10

Re: Genapts failure on EIDW

Postby legoboyvdlp » Wed Oct 03, 2018 8:43 pm

I'll check but I know for a fact one of them does (since I made the ATC network myself) and that airport was generated fine.

I'll try simplifying the layout.
User avatar
legoboyvdlp
 
Posts: 5832
Joined: Sat Jul 26, 2014 1:28 am
Callsign: YV-LEGO
Version: 2018.3.1
OS: Windows 10 HP

Re: Genapts failure on EIDW

Postby xDraconian » Thu Oct 04, 2018 12:09 am

TerraGear will load an apt.dat up to version 1100, but it does nothing with those newer features.

Jonathan,
A couple of ideas to try:
Create a EIDW.dat file containing only EIDW. Any change?
Load your dat file into WED to confirm the file is valid.
Remove the items at the point that the process stops to see if it then runs to completion. Then add items back slowly until you identify the item it does not like. Maybe there is a bug in the loader.

Scott
xDraconian
 
Posts: 86
Joined: Sun Jan 21, 2018 5:53 am
Version: Git
OS: Linux Mint

Re: Genapts failure on EIDW

Postby wlbragg » Thu Oct 04, 2018 12:11 am

I'll try simplifying the layout.

That's what I am getting at, I have had airports fail because of a line or two that when removed fixed the issue. I was never able to determine why though.
Kansas(2-27-15)/Ohio/Midwest scenery development.
KEQA (2-27-15), 3AU, KRCP Airport Layout
User avatar
wlbragg
 
Posts: 4183
Joined: Sat Aug 25, 2012 11:31 pm
Location: Kansas (Tornado Alley), USA
Callsign: WC2020
Version: next
OS: Win10/Debain/nVGT640

Next

Return to Scenery

Who is online

Users browsing this forum: No registered users and 6 guests